Hi folks, today, we will learn how to setup Wireguard as VPN on Ubuntu.
This tutorial has been tested on Ubuntu 20.04.
Keep also in mind that Wireguard is different than OpenVPN for example because there is no concept of client/server, but only peers. So in my example, I will be using the Ubuntu as a « server » and the iOS as a « client » but in reality it’s just a point to point VPN between two machines.
Wireguard is already included in Ubuntu’s main repositories so you only have to call APT to install it:
apt install wireguard
As Wireguard is a kernel module, you will need to check if it’s enabled and enable it if it’s not.
To check if you will have to do so:
lsmod | grep wireguard
If it’s ok, you will get something like this:
If you get nothing, you will have to enable it either :
- Manually for one time:
- Automatically so it starts at boot:
echo "wireguard" > /etc/modules-load.d/wireguard.conf
In my fresh Ubuntu installation, I had to enable it manually.
Configuration on Ubuntu
There are many ways to configure Wireguard. I will present you one that works but feel free to research for other methods.
Wireguard works kinda like OpenSSH, each peer have a pair of private and public key but unlike OpenSSH, Wireguard needs to know each public keys and private IP address of each peer he will allow the connection.
All the following commands will be performed on Ubuntu which as said previously will be our « server ».
Create private and public keys
mkdir /etc/wireguard cd /etc/wireguard wg genkey | tee privatekey | wg pubkey > publickey
Then, create a configuration file for wg0 which will be our device for routing.
[Interface] Address = 192.168.2.1/24 ListenPort = 51820 PrivateKey = SERVER_PRIVATE_KEY # note - substitute eth0 in the following lines to match the Internet-facing interface # if the server is behind a router and receive traffic via NAT, this iptables rules are not needed PostUp = iptables -A FORWARD -i %i -j ACCEPT; iptables -t nat -A POSTROUTING -o eth0 -j MASQUERADE PostDown = iptables -D FORWARD -i %i -j ACCEPT; iptables -t nat -D POSTROUTING -o eth0 -j MASQUERADE [Peer] # iphone PublicKey = PEER_IPHONE_PUBLIC_KEY AllowedIPs = 192.168.2.2/32
Adress: Here we define a network in /24, feel free to change it.
ListenPort: We also make our “server” listen on port 51820 in UDP so don’t forget to open it in your firewall(s).
PrivateKey: Replace SERVER_PRIVATE_KEY by the content of /etc/wireguard/privatekey.
Leave PEER_IPHONE_PUBLIC_KEY for now, we will replace it after with our client’s public key.
AllowedIPs: Change the AllowedIPs if you change the network or if you want to attribute another IP to your peer/client.
We will host “clients” keys and configuration files on the “server” in that example. But you can also generate them on your client and keep them safely there. It’s up to you.
Create a new directory to put client’s configuration files
mkdir -p /etc/wireguard/clients/iphone
Generate private and public keys
cd /etc/wireguard/clients/iphone wg genkey | tee privatekey | wg pubkey > publickey
Create client’s configuration file
[Interface] Address = 192.168.2.2/24 PrivateKey = PEER_IPHONE_PRIVATE_KEY DNS = 192.168.2.1 [Peer] PublicKey = SERVER_PUBLICKEY AllowedIPs = 0.0.0.0/0, ::/0 Endpoint = ubuntu.mydomain.com:51820
Address: Client’s IP address, it has to match the one you defined in the server’s configuration.
PrivateKey: Replace PEER_IPHONE_PRIVATE_KEY by the content of /etc/wireguard/clients/iphone/privatekey
DNS: Put whatever DNS you want.
PublicKey: Replace SERVER_PUBLICKEY by the content of /etc/wireguard/publickey.
AllowedIPs: Allow specific IP if it’s a static one or all if it’s dynamic IP.
Endpoint: Specify the hostname or IP of your server and the port.
In /etc/wireguard/wg0.conf, replace PEER_IPHONE_PUBLIC_KEY by the content of /etc/wireguard/clients/iphone/publickey
Start Wireguard at boot
You can simply use systemd and wg-quick to enable and start your interface:
Mobile clients configuration
Create configuration manually
This is self-explanatory, you actually create the config on the mobile device then transfer the relevant keys to the server’s config.
Create configuration from archive
Here you have to create a .zip archive of the client configuration file, transfer it to the device then import it into the app.
Import by reading a QR code (most secure method)
The mobile client supports QR code based input.
You need to install qrencode to generate a qr code from a configuration file:
apt install qrencode
Then call qrencode and pass the client configuration:
qrencode -t ansiutf8 < client.conf
This will generate a QR code that is readable by the mobile client.
The advantage of this approache is that there is no need to transfer sensitive information via data channels that can potentially be compromised and there is no need of any other supplementary software besides a terminal or console.
I hope you enjoyed this small tutorial about WireGuard on Ubuntu.
Feel free to comment below :D